Home Products News Contact Us
Home > Supports > Diesel Engine

Solutions for Oil Or Gas Leakage in Diesel Generator Sets

Dec. 10, 2021

Do you know what solutions are there for oil leakage, water leakage or air leakage in diesel generator sets? When diesel generator sets have oil leakage, water leakage or air leakage, it will cause diesel generators to increase fuel consumption, accelerate component wear, and reduce power, etc. Fault. Therefore, it must be repaired in time. The following is the treatment method when the diesel generator set has oil leakage, water leakage, and air leakage. First, the size recovery glue is used to cure the leakage. The shaft and sleeve, bearing and bearing seat, valve and valve seat, self-tightening oil seal, When the felt cups and packing fillers leak, the size recovery glue can be applied to the cleaned and worn parts of the mating parts. After curing, a wear-resistant, heat-resistant, and mechanically strong film layer is formed. Carry out machining, such as turning, boring, scraping, filing, etc., to restore the geometric shape and matching accuracy of the parts, so as to solve the leakage problem.


backup power generator.jpg


Leakage control of paint chip liquid, leakage at the joints of diesel fuel tank, water tank, crankcase, etc., after soaking the paint chip in alcohol, apply the paint chip liquid to the cleaned joints to cure the leakage. However, the cost of lacquer chips is high, and they are generally used in emergencies. Leakage control method with viscose glue, when the body parts of the diesel engine, such as blisters and pores in the fuel tank, water tank, oil pipe, water pipe, etc., cause leakage, apply viscose glue to the cleaned damaged area, and then the leakage can be cured. Effect. With the oil leakage control method, when the paper pads of diesel engine oil pan, cylinder head, gear cover, crankcase rear cover, etc. leak, as long as the paper pad is intact and the joint surface is clean, you can apply a piece of paper on both sides of the paper pad. Use a layer of butter and tighten the bolts to prevent leakage. If you change to a new paper pad, soak the new paper pad in diesel for 10 minutes before installation, then take it out and wipe it, and put a layer of butter on the joint surface before installing it.


Anaerobic glue is used to control leakage. When there is leakage in the vent bolts, stud bolts, plugs, etc. on the diesel generator set, apply anaerobic glue to the cleaned bolts, threads or screw holes, which can quickly solidify and form The film fills the gaps of the parts and can withstand greater pressure. At the same time, it also has the fastening function of strong shock resistance and anti-looseness. If it is used at the thread of the diesel engine high pressure oil pipe joint, the leakage control effect will be better. Liquid sealant leak control method, when solid gasket defects appear on diesel generator sets to form interfacial leakage and destructive leakage, apply liquid sealant on the cleaned solid gasket joint surface, which can form uniform and stable after solidification , The peelable film gasket with continuous adhesion can prevent all leakage. Padded leak control method, oil leakage at the leak-proof gasket of diesel oil pipe joints, a layer of double-sided smooth thin plastic gaskets can be added on both sides of the leak-proof gasket, and the leak can be prevented by tightening it forcefully.


Starlight Power was founded in 1974 and is one of the earliest manufacturers of generators and diesel generator sets in China. If you want get more information, please feel free to send email to sales@dieselgeneratortech.com we will pay highly attention on your question.

Contact Us
  • Adds: No.2 Xingguang Road, Guxi Industrial Park, Taixing, Jiangsu, China.
  • Tel: +86 771 5805 269
  • FAX: +86 771 5805 259
  • Cellphone: +86 134 8102 4441
                    +86 138 7819 8542
  • E-mail: sales@dieselgeneratortech.com
Follow Us

Copyright © Jiangsu Starlight Electricity Equipments Co., Ltd.All Rights Reserved | Sitemap

Contact Us